-40%
*New* Lime Microsystems LimeNET Micro 10 MHz - 3.5 GHz Transceiver
*New* Lime Microsystems LimeNET Micro 10 MHz - 3.5 GHz Transceiver
*New* Lime Microsystems LimeNET Micro 10 MHz - 3.5 GHz Transceiver
*New* Lime Microsystems LimeNET Micro 10 MHz - 3.5 GHz Transceiver
*New* Lime Microsystems LimeNET Micro 10 MHz - 3.5 GHz Transceiver
*New* Lime Microsystems LimeNET Micro 10 MHz - 3.5 GHz Transceiver
*New* Lime Microsystems LimeNET Micro 10 MHz - 3.5 GHz Transceiver
*New* Lime Microsystems LimeNET Micro 10 MHz - 3.5 GHz Transceiver

*New* Lime Microsystems LimeNET Micro 10 MHz - 3.5 GHz Transceiver

$ 316.28

  • Band: AM, AM/FM, FM, UHF, VHF
  • Brand: Lime Microsystems
  • Frequency Range: 10 MHz - 3.5 GHz
  • Model: LimeNET Micro
  • Number of Channels: 2
  • Supported Modes: AM, CW, SSB, QRP, FM
  • Type: Ham Radio Transceiver

Description

Brand new in box LimeNET Micro Transceiver (10 MHz - 3.5 GHz). This unit combines the full power of the LimeSDR on a development board with a Raspberry Pi compute module. Board is still in factory sealed anti-static bag. Please email with any questions. Will ship next business day via USPS Priority Mail. LimeNET Micro makes deploying wireless networks more accessible than ever before, by extending the LimeNET line of integrated hardware solutions via an ultra-low cost platform that is capable of supporting narrowband systems, such as GSM and IoT wireless standards, in a stand-alone configuration. Features and Specifications Feature Description RF Transceiver Lime Microsystems LMS7002M MIMO FPRF FPGA Intel MAX 10 (10M16SAU169C8G 169-UBGA) Raspberry Pi Raspberry Pi CM3(L) USB 2.0 controller FTDI FT601 (connects FPGA to USB2.0 HUB) Oscillator Rakon U7475LF @30.72MHz Continuous frequency range 10MHz - 3.5 GHz Bandwidth Up to 10 MHz RF connection 2 SMA connectors (2 TRX) Power Output (CW) Up to 10 dbm Power Supply Via PoE, external 5V DC connector or microUSB port Status indicators Programmable LEDs Dimensions without connectors 125mm x 65mm LimeNET-Micro board features: RF transceiver Lime Microsystems LMS7002M Raspberry Pi DDR2 SODIMM socket for raspberry Pi CM3(L) 2x downstream USB 2.0 ports Upstream Micro-USB for USB boot of Compute Module 3.5mm analog audio, composite video output Ethernet + active PoE (RJ45) connector Ribbon cable camera and display connectors HDMI connector External UART connector uSD card slot USB2.0 HUB and 10/100 Ethernet controller SDIO Wi-Fi module Jumper for Raspberry boot mode selection FPGA Features Intel MAX10 10M16SAU169C8 device in 169-pin UBGA 16K logic elements 549 Kbits embedded memory (M9K) and 2368 Kbits of user Flash Memory 45 embedded 18x18 multipliers 1 PLLs FPGA Configuration JTAG mode configuration USB Controller FTDI FT601 USB to FIFO interface bridge chip (connects FPGA to USB2.0 HUB) Memory Devices 4Mbit FLASH (for FPGA data) 2x 128Kbit (16K x 8) EEPROM (for LMS MCU firmware and FPGA data) Other Devices Temperature sensor Crypto Authentication Device GNSS receiver Connections 2 x coaxial RF (SMA) connectors SMA connectors for reference clock IN/OUT, GNSS and Wi-Fi antennas 5V DC power jack 5V header for powering external devices Fan header FPGA JTAG connectors (0.05” pitch and side connector) Backup battery connector for GNSS receiver Clock System 30.72MHz VCOCXO: Frequency calibration ±0.5ppm; Frequency stability over temperature in still air ±20ppb; Frequency slope ΔF/ΔT in still air ±1.2ppb/°C Possibility to tune VCOCXO by onboard DAC Possibility to use GNSS PPS signal as a reference when tuning VCOCXO frequency User I/O GPIO header (0.05” pitch) connected to FPGA 5X dual color (RG) LEDs connected to FPGA Push button connected to FPGA Buzzer connected to FPGA Board Size: without connectors 125mm x 65mm (4.92” x 2.56”)